| Item | Where? | Torque | Notes |
|---|---|---|---|
| Ball Joint Stud Nut, Lower | Front | 80 pound-feet | |
| Ball Joint Sleeve, Upper | Front | 50 pound-feet | |
| Ball Joint Stud Nut, Upper | Front | 100 pound-feet | |
| Brake Backing Plate | Front | 30 pound-feet | Drum Brakes |
| Brake Shield Plate | Front | 10 pound-feet | Disc Brakes |
| Brake Shield Plate Mounting Bracket | Front | 35 pound-feet | Disc Brakes |
| Brake Caliper Pins | Front | 35 pound-feet | |
| Lower Kingpin Bearing Cap Screws | Front | 85 pound-feet | |
| Seal Retaining Screws | Front | 20 pound-feet | Disc Brakes |
| Spindle Bearing Locknut, Inner | Front | 50 pound-feet | After torquing, turn wheel and then back nut off ¼-turn |
| Spindle Bearing Locknut, Outer | Front | 50 pound-feet | |
| Brake Backing Plate | Rear | 30 pound-feet | |
| Differential Carrier Bearing Cap Screws | Centre | 80 pound-feet | |
| Differential Cover Screws | Centre | 35 pound-feet | |
| Pinion Yoke Nut | Centre | 200 pound-feet | May tighten to achieve specified preload |
| Pinion Shaft Preload (torque to turn) | Centre | 20 to 40 pound-inches | With new bearings |
| Ring Gear Screws | Centre | 60 pound-feet | Alway Use New Screws! |
| Dana 44-4 Axle used in Jeep Grand Cherokee (WJ) Rear | |||
| Cross Shaft Lock Screw | 44-4 (WJ Rear) | 12 pound-feet | |
| Differential Carrier Bearing Cap Screws | 44-4 (WJ Rear) | 65 pound-feet | |
| Differential Cover Screws | 44-4 (WJ Rear) | 32 pound-feet | |
| Retainer Plate | 44-4 (WJ Rear) | 45 pound-feet | |
| Ring Gear Screws | 44-4 (WJ Rear) | 80 pound-feet | Always Use New Screws! |
| Dana 44, Independent Rear Suspension (44 IRS) | |||
| Differential Carrier Bearing Cap Screws | 44 IRS | 85 pound-feet | |
| Differential Cover Screws | 44 IRS | 35 pound-feet | |
| Retainer Plate Screws | 44 IRS | 40 pound-feet | |
| Pinion Yoke Nut | 44 IRS | 200 pound-feet | May tighten to achieve specified preload |
| Pinion Shaft Preload (torque to turn) | 44 IRS | 20 to 40 pound-inches | With new bearings |
| Ring Gear Screws | 44 IRS | 60 pound-feet | Always Use New Screws! |
| Dana 44, Independent Rear Suspension, Aluminum Centre Section (44 Al IRS) | |||
| Pinion Yoke Nut | 44 Al IRS | 200 pound-feet | May tighten to achieve specified preload |
| Pinion Preload (torque to turn) | 44 Al IRS | 15 to 35 pound-inches | With new bearings |
| Ring Gear Screws | 44 Al IRS | 60 pound-feet | Always Use New Screws! |
| Hub-Lok (External Type) for Dana 44 Front Axles | |||
| Hub Cover Screws | Hub-Lok | 32 pound-feet | |